Garage Server Rack

Garage Server Rack – This will connect my 12u rack in my garage to the main network 10g

In the extended garage I needed some networking for the access point, flight tracking setup, 3 x PoE cameras and future additions, and instead of running lots of Cat6 cables, I wanted to run some OM3 fibers on the other end. This way I have 10G bandwidth at home and can add as many devices as I want. Running cables through the small breezeway that connects the garage to the house is tricky, so I only need it once. Being fiber eliminates the possibility of lightning as some devices have longer antennas.

Garage Server Rack

I posted this on /r/homelab, but it was removed because it was unrelated to Homelab. Spread out there as usual. I’d like to share how I install it, and I haven’t found any good full instructions or posts where someone has done it successfully outside of a commercial environment. In fact, nothing goes right, everything becomes a mess, just like in my garage… All the details are here

Server Cabinet Cooling

First I bought 60m OM3 from Fiberstore, Cisco WS-C2960S-48LPD-L with 2 x 10G SFP+ ports and 48 Po+ ports. The switch consumes about 30W of power at idle, so that’s not too bad for a relatively low purchase price.

First I ran the fiber through my closet. I got an LC keystone so I can run a short patch cable to the switch

He went into the attic and into the garage entrance wall. The hole in the wall is still a bit temporary…I’ll clean up eventually. Aqua cable is fiber

Here you can see where it comes up in the garage (it’s been fixed a lot since then, so ignore the mess) As you can see on some of the water lines, I ran 1/2 stainless steel pipe into the vent the first day. I went home to have AT&T run their fib to my house and that’s all I got on short notice at 9:30pm, so I opted for it.

The Homelab Adventure Begins! :: Cavelab Blog — Stories From The Cavelab

Before installing the shelf, I put it on the bench to test the connection. I had a spare APC SMT1000RM2U so I decided to use that.

I left it here and monitored the temperature for a week and everything seemed fine. To install the shelf

I tore out the old wood paneling (?) on the wall to expose the studs I wanted to put in. Unfortunately the stems were 24″ on center, not 16″ on center, as the rack mounting brackets were designed for. Very loose stud, had some crappy power near normal. The hat was also eaten away by rats (or something) and it seemed that way for a while

I went ahead and tore off the old cover and placed a 2×4 stud 16″ across the good one. This gave me room to hang the rack. I flipped the loose stud over to the one next to it. Installed protectors for it. Electrically, this was one of my first DIY jobs, so my skills were a little rusty, and I now have things figured out. I’m sure you understand. I could clean it up a bit, but it all works

The Home Data Center: Man Cave For The Internet Age

I ran a new 20a circuit for the rack. I’m switching in a new, much larger panel, so providing a separate circuit was a no-brainer

I installed 15/32 plywood on the wall and attached it with some screws. I cut a hole for an old work electrical box. I began to cut the hole with a very strong blade, which reduced the wood, next time …

Here it has the containers installed. I don’t like the front plate, may change that later

Next I drilled a few holes in the top to route the cables through. The brush plates were over $5 each, which is crazy, so I used these 60c dryer plates.

Rack That Server

If I put them at an angle so the hole is big enough for the screw heads, I start to wobble a little

Next to install the UPS. Unfortunately the bottom u of the shelf has some clearance issues so I removed the bottom 1u

It’s not a 4 post shelf so I flipped the rails to the back panel and works great

I installed the outlets in the correct position and made sure the shelf was extended enough to have plenty of clearance.

My Home Data Center

Automated PHP Upgrade for LibreNMS I put off updating PHP on my LibreNMS box to 8.1 for a while, but thought I’d finally take a crack at it. I was at 7.3 and I had to get to 8.1. I’m running Debian 10 and on this machine I’m only running LibreNMS. If you

If you’ve read my previous posts about deploying a TrueNAS backup server into my hot Texas garage, you know I have it in an unequipped garage with Cisco switches, an APC UPS, two Raspberry Pis, and other stuff. Everyone told me it wouldn’t work in summer because it’s so hot

This post will go over my experience installing some mini split ACs to give you a second chance at heating and cooling multiple heating and cooling energy savings using mini split heat pumps. A few months after I moved into my house, my AC compressor died. It was August, the height of summer here, and having the server rack in the garage over the winter didn’t allow me to do much, so I started building a room for it.

Buy two 4ft x 9ft double glass doors, adjust them to fit and put some wheels underneath. The idea is to use a rail at the top and bottom, and the doors are mounted on wheels.

The Best Home Network Rack

I then used 3 white square vinyl moldings as spacers and two pairs of oak pieces to make side rails for both doors.

I used 4 long L shaped moldings to make the top path and nailed them to the ceiling. The doors go first to the top track and then to the floor rail, which looks like this.

To cool the room, there is an A/C unit in the window during hot days and partially open in winter. I used 3 inches of foam on the sides and elastic bands on the bottom.

To protect against noise, I hang DB-4 vinyl on walls and ceilings. Since it’s a mess with lots of cutting and glue and staples, I only get a few pictures. Also, the foam needs to be removed so that the panels fit well.

The Sweat Shop. My Homelab I Run In A Fl Garage.

There were exits on the walls on both sides, which I tried to make new runs into the panel. Two independent 20A circuits should give me enough power for the rack, cooling and a few lights, plus extra time if I need to cut power to one side.

Since the garage is mostly open and I cut out most of the wood panels inside, there was dust everywhere, including the shelves. He took everything apart, took off the side panels and doors and started cleaning in earnest.

With the help of a good friend, he got off the shelf and into the room. Now the work goes back and attaches everything.

After 5 hours, the side profile looks like this. You can see the A/C unit installed in the window.

My Home Network Update

With everything tested and working fine, I cleaned up and installed the side panel so it looked clean. Doors and other side still open (too cold to leave dust).

That’s it! The entire project took me 60-plus hours, but spanned over 2 months. I now have a sound and weather proof room with two dedicated circuits to store all my stuff!!! A dream come true… It’s been a year and a half since we moved into our new house and I finally locked the servers in the garage. It looks great compared to my old setup.

Two DELL OptiPlex 990 small form factor machines with Windows Server 2008 R2 as Hyper-V servers. One server ran the required 24/7 VMs and the other was used to test and test the VMs. The 24/7 VM includes a W2K8R2 domain controller and a W2K12 file server.

For storage I used a Synology DS2411+ NAS with 12

Brother Led Printer Review

Overhead garage storage rack, server rack, garage storage rack systems, server rack in garage, electric garage storage rack, storage rack for garage, garage wall rack system, garage rack installation, rack garage storage system, garage storage rack installation, garage rack, hanging rack for garage